Technical register for agricultural, construction and commercial machinery · sourced data

Sany STC500

Series: Sany Hydraulic Truck Crane

Source: sany.in

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Sany STC500 belongs to the Sany Hydraulic Truck Crane series. The engine delivers 340 hp (250 kW). Torque is 1,425.1 Nm. Rated speed is 2,100 rpm. The unladen weight is 42,000 kg. Ground clearance is 295.7 mm. Maximum torque is reached at 1,200 rpm. The electrical system runs on 24 V. Tyre size: 12,00R20-20PR×12. The Sany Hydraulic Truck Crane series covers 6 models. Rated output within it ranges from 289.7 to 373.9 hp; the STC500 sits in the middle of that range with 340 hp. Its immediate neighbours are the STC250H below it with 289.7 hp and the STC750 above it with 373.9 hp. Unladen weight within it ranges from 26,400 to 46,000 kg; here the STC500 sits in the upper part of that range with 42,000 kg. 87 Sany models across 17 series are on record.

Sany Hydraulic Truck Crane – the QY25C and the STC range from STC200 to STC750, 213 to 275 kW, 26 to 46 tonnes crane vehicle weight

Sany, founded in 1989 in Hunan and headquartered in Changsha, ranks among China's largest construction-equipment makers and among the leading truck-crane brands worldwide. The type logic: QY is the standardised Chinese abbreviation for a truck crane (a crane on its own chassis), and the following number gives the maximum lifting capacity in tonnes – QY25C is thus a 25-tonne crane. Sany's own STC range (Sany Truck Crane) follows the same logic: STC200 to STC750 denote capacities of 20 to 75 tonnes, with H marking a version with greater hook height.

Read on 3 more paragraphs

The register lists here 6 versions with 213 to 275 kW, all from six-cylinder engines, crane vehicle weights from 26,400 to 46,000 kg, torque from 1,050 to 1,500 Nm and a rated speed of about 2,100 rpm.

Truck cranes in this class lift loads of 20 to 75 tonnes on building sites, at installation work and in civil engineering, and travel to the job on public roads on their own chassis. From the 2000s Sany's STC range competed against established suppliers such as Liebherr and Tadano and the Chinese rivals XCMG and Zoomlion, building the brand's share of the mid-capacity segment.

On a used truck crane, the condition of the telescopic boom and its sliding pads, the hoist winch and wire ropes, the hydraulic cylinders of boom and outriggers, the chassis and axles for road use, and the inspection history of the crane superstructure, which in most countries must be periodically examined by a qualified inspector, all count. Spare parts run through Sany's international dealer network.

Sources: SpecCodex register, model data: Sany Hydraulic Truck Crane, Sany Group (manufacturer)

Technical data

Engine

Power340 hp (250 kW)correct
Rated speed2,100 rpmcorrect
Torque1,425.1 Nmcorrect
Speed at max. torque1,200 rpmcorrect

Dimensions and weights

Ground clearance295.7 mmcorrect
Unladen weight42,000 kgcorrect

Drivetrain and chassis

Tyre size12.00R20-20PR×12correct

Other data

System voltage24 Vcorrect

Where this model stands

Power-to-weight ratio: 6 kW/t (250 kW / 42 t)

Stronger than 56% of the mobile & rough terrain cranes in the register — out of 723 models with a stated power figure.

Calculated from the documented figures above — not a rating.

Frequently asked questions

How much power does the Sany STC500 have?

The Sany STC500 delivers 340 hp.

How much does the Sany STC500 weigh?

The unladen weight is 42,000 kg.

What to check before buying

  • Check the hour meter against the service records — a replaced instrument is the most common gap.
  • Compare the data plate and chassis number with the papers.
  • Check the weights in the papers against the figures here — attachments change them.
  • Ask about parts availability for this build year — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 9 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: RitchieSpecs equipment specifications (retrieved August 2026) · How we check the data

Mobile crane in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare