Holder E9/E9D
Built: 1974–1990 · Series: E-Reihe
More machines from model year 1974
Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required
Holder E series – the single-axle tractors from Metzingen: E 3 to E 14, the number as hp class, B, F and D for petrol, bought-in engine and diesel, single-cylinder two-strokes and small diesels of 75 to 600 cm³
Holder of Metzingen at the foot of the Swabian Alb has been at home in crop protection since 1888 and from the 1930s built single-axle tractors for vineyards, vegetable growing and smallholdings – the E series is that programme: E stands for the single-axle tractor (Einachser), the number orders the size by hp class in ascending order, from the E 3 with three hp to the E 14; the letters on the E 8 mark the engine, B for petrol, F for the bought-in engine (Fremdmotor) and D for the diesel, and E9D is the diesel version of the E 9. The engines are single-cylinders: two-stroke petrol engines running on 1:25 mixture in the small types, small diesels in the larger ones, with displacements of 75 to 600 cm³ and rated speeds up to 4,500 rpm – the two-strokes rev high, the diesels run slowly. The single-axle tractor carries a rotary tiller, plough, cutter bar, sprayer or trailer and is guided by handlebars; until the 1960s it was the vintner's and gardener's tractor before the articulated four-wheel tractors of the Holder A series replaced it.
Read on 3 more paragraphs
The register lists 9 versions with 1.9 to 9 kW from single-cylinders of 75 to 600 cm³; widths of the small types are 415 mm, heights between 730 and 1,030 mm.
Holder single-axle tractors are collectors' pieces today and in steep-slope viticulture partly still in use because they fit into rows no four-wheel tractor can enter.
On used machines, compression and ignition of the two-strokes, clutch and gearbox, the condition of handlebars and implements and parts supply, which for the engines runs through vintage specialists, are what count.
Sources: SpecCodex register, model data: Holder E-Reihe, Max Holder GmbH (manufacturer)
Technical data
Engine
| Fuel | Benzin/Dieselcorrect |
|---|---|
| Power | 8.5 hp (6.2 kW)correct |
| Rated speed | 3600–4500 rpmcorrect |
| Cylinders | 1correct |
| Displacement | 202 cm³correct |
| Cooling | air-cooledcorrect |
Dimensions and weights
| Length | 1,950 mmcorrect |
|---|---|
| Width | 609 mmcorrect |
| Height | 985 mmcorrect |
| Unladen weight | 150 kgcorrect |
Drivetrain and chassis
| Drive | single-axle drivecorrect |
|---|---|
| Gearbox | 4/3correct |
| Front tyres | 6.00-9 AScorrect |
| Top speed | 20 km/hcorrect |
Origin and approval
| Construction | unit construction (no separate frame)correct |
|---|---|
| Units built | ca. 6.200 Stückcorrect |
Where this model stands
Power-to-weight ratio: 41.3 kW/t (6 kW / 0.1 t)
Power class: Compact (< 40 hp)
Stronger than 1% of the tractors in the register — out of 15,663 models with a stated power figure.
Calculated from the documented figures above — not a rating.
Frequently asked questions
How much power does the Holder E9/E9D have?
The Holder E9/E9D delivers 8.5 hp.
How much does the Holder E9/E9D weigh?
The unladen weight is 150 kg.
What engine does the Holder E9/E9D have?
1 cylinders, 202 cm³ displacement, Benzin/Diesel.
How fast does the Holder E9/E9D go?
Top speed is 20 km/h.
What are the dimensions of the Holder E9/E9D?
1,950 mm × 609 mm × 985 mm.
When was the Holder E9/E9D built?
Production years: 1974–1990.
What to check before buying
- Check the hour meter against the service records — a replaced instrument is the most common gap.
- Compare the data plate and chassis number with the papers.
- Check the weights in the papers against the figures here — attachments change them.
- Check front and rear tyre sizes: mismatched pairs strain the drivetrain.
- Shift the gearbox cold and warm — jumps only show up at temperature.
- Load the hydraulics and watch for sag.
- Ask about parts availability for this build year — the running costs hang on it.
A general list for this type of machine — no substitute for an inspection or an appraiser.
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
We ask the suppliers and come back with price and lead time.
Request spare parts →
This page carries 17 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.
Missing a figure you were looking for? Report it →
Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →
Other models in this series
Sources: [1]
Tractor in 3D section
Turn the model, look inside and click an assembly — each one is explained.