Technical register for agricultural, construction and commercial machinery · sourced data
Start › Electric motors › Donstak › Other models › YE2-112M-2

Donstak YE2-112M-2

Series: Other models

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Donstak YE2-112M-2 is a three-phase induction motor built by Donstak. The rated output is 4 kW. The motor is two-pole, which at 50 Hz gives a synchronous speed of 3,000 rpm. The rated voltage is 415 V. The housing is frame size 112 M in foot-mounted form. The protection class is IP44. The efficiency is 87.8 per cent at full load, 88 per cent at 75 per cent load and 85.5 per cent at half load. The motor weighs 38 kg. The mounting arrangement to IEC 60034-7 is B3. The motor is built in China. The figures come from the Australian MEPS register under standard AS/NZS 1359.5:2004; measured to IEC 60034-2-1 (Edition 2.0). Rated output within this group ranges from 0.18 to 1,119 kW; the YE2-112M-2 sits at the bottom of that range with 4 kW. Its immediate neighbours are the DNGW-112MB-04 below it with 3.8 kW and the FF112M-4 above it with 4.5 kW.

Donstak – other models: the collective page of MEPS-registered YE2 three-phase motors outside the named ranges, frame sizes 112 to 132, 4 to 7.5 kW, two-pole, IP44 protection

This page gathers the Donstak three-phase motors the Australian energy-efficiency register could not assign to a named range. The designations recorded in the register, YE2-112M-2 and YE2-132S2-2, follow the YE scheme common in China: YE2 denotes the range, the digit sequence the IEC frame size (112, 132), the letter the build length (M, S), and the final digit the pole count (2 in both cases here).

Read on 3 more paragraphs

The register lists here 2 versions with 4 to 7.5 kW rated output, both two-pole, for a 415 V supply, with full-load efficiencies from 87.8 to 89.7% and at 75% load from 88.01 to 89.98%. Protection is IP44, frame sizes run from 112 to 132, the mounting code is B3 (foot type). Manufacturing takes place in China, testing followed AS/NZS 1359.5:2004 with test method B.

The YE2 mark in the model name is the designation common in China for the standard efficiency class, corresponding to the IE2 level under IEC 60034-30-1; two-pole motors of this power class run at 3,000 rpm at 50 Hz and drive high-speed pumps, compressors and fans. The IP44 rating – dust-protected and protected against splashing water from all directions – suffices for use in dry to moderately humid interiors, but not for open outdoor use.

When buying used, bearing condition and a checked insulation resistance of the winding, the condition of the terminal box and fan cover, the condition of shaft and key, and a legible nameplate with frame size, pole count and protection rating matter; since IP44 offers no protection against jetting water, corrosion in the terminal box is especially worth checking on motors from outdoor use. Spares run through Donstak's distribution.

Sources: SpecCodex register, model data: Donstak (weitere Modelle, MEPS-Registrierungen)

Technical data

Engine

Rated output4 kWcorrect

Dimensions and weights

Weight38 kgcorrect

Electrical data

Rated voltage415 Vcorrect
Number of poles2correct
Protection classIP44correct
Frame size112 M (foot)correct
Mounting (IEC 60034-7)B3correct
Efficiency at full load87.8 %correct
Efficiency at 75 % load88.01 %correct
Efficiency at half load85.46 %correct

Origin and approval

Country of manufactureChinacorrect

Other data

Standard appliedAS/NZS 1359.5:2004correct
Test methodIEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the Donstak YE2-112M-2 have?

The Donstak YE2-112M-2 delivers 4 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 23 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: Energy Rating — Australian government equipment register (retrieved August 2026) · How we check the data

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare