Start › Tractors › Zetor › HT 45

Zetor HT 45

Series: Utilix

Source: https://www.lectura-specs.com/en/model/agricultural-machiner

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The HT 45 from Zetor is part of the Utilix series. The engine delivers 43 hp (31 kW), has 4 cylinders, with a displacement of 2,216 cm³. Rated speed is 2,600 rpm. The machine is 3,590 mm long, 1,620 mm wide and 2,530 mm high. The unladen weight is 1,900 kg. The wheelbase measures 1,835 mm. Ground clearance is 350 mm. Top speed is 28 km/h. Lifting capacity is 1,500 kg. Transmission: 3 stufig hydrostatisch. The engine is water-cooled. The fuel is diesel. Rated output across the Zetor range ranges from 15 to 160 hp; the HT 45 sits in the lower part of that range with 43 hp. Its immediate neighbours are the Super-P below it with 42 hp and the 3321/3341 Super above it with 45 hp. Rated output across the Zetor range ranges from 22 to 160 hp; here the HT 45 sits in the lower part of that range with 43 hp. 371 Zetor models across 27 series are on record.

Zetor Utilix: the compact tractor from Brno of the 2010s, HT 45 and HT 55 with a four-cylinder diesel engine, 31 to 36 kW, 2,216 cm³, 1,900 kg unladen weight, 1,500 kg lift capacity

This page lists the Zetor Utilix, the compact tractor from the Czech maker in Brno dating from the 2010s, with the HT 45 and HT 55 types, whose type number roughly matches the power class in hp (HT 45 with about 43 hp, HT 55 with about 49 hp). The range targets smaller farms, municipalities and horticulture looking for a simple, compact tractor with a four-cylinder engine and hydraulics sufficient for basic attachments.

Read on 4 more paragraphs

The register lists here 2 versions with 31 to 36 kW, or 43 to 49 hp, from a 2,216 cm³ four-cylinder engine, an unladen weight of 1,900 kg, a lift capacity of 1,500 kg, a length of 3,590 mm, a width of 1,620 mm and a height of 2,530 mm; the engines run at 2,600 to 2,800 revolutions per minute.

The Utilix positions itself below Zetor's classic ranges as an affordable entry-level tractor and competes with compact models from Asian and Western European makers in the same power class for municipalities, horse keepers and small farms, where simple engineering and low running costs matter most.

On used examples, operating hours, the condition of engine and clutch, the function of hydraulics and PTO, and rust on cab and sheet metal count; parts run through the Zetor dealer network.

In this power class of 31 to 36 kW, the ISO 730 three-point linkage is as a rule Category I, with the PTO running at the standard 540 rpm speed – enough for mulchers, sweepers and other municipal implements.

Sources: SpecCodex register, model data: Zetor Utilix, Zetor

Technical data

Engine

Fuel	dieselcorrect
Power	43 hp (31 kW)correct
Rated speed	2,600 rpmcorrect
Cylinders	4correct
Displacement	2,216 cm³correct
Cooling	water-cooledcorrect

Dimensions and weights

Length	3,590 mmcorrect
Width	1,620 mmcorrect
Height	2,530 mmcorrect
Wheelbase	1,835 mmcorrect
Ground clearance	350 mmcorrect
Unladen weight	1,900 kgcorrect

Drivetrain and chassis

Gearbox	3 stufig hydrostatischcorrect
Top speed	28 km/hcorrect

Working data

Lifting capacity	1,500 kgcorrect

Where this model stands

Power-to-weight ratio: 16.3 kW/t (31 kW / 1.9 t)

Power class: Universal (40–100 hp)

Stronger than 27% of the tractors in the register — out of 15,663 models with a stated power figure.

Calculated from the documented figures above — not a rating.

Frequently asked questions

How much power does the Zetor HT 45 have?

The Zetor HT 45 delivers 43 hp.

How much does the Zetor HT 45 weigh?

The unladen weight is 1,900 kg.

What engine does the Zetor HT 45 have?

4 cylinders, 2,216 cm³ displacement, Diesel.

How fast does the Zetor HT 45 go?

Top speed is 28 km/h.

How much does the rear linkage of the Zetor HT 45 lift?

The rear linkage lifts 1,500 kg.

What are the dimensions of the Zetor HT 45?

3,590 mm × 1,620 mm × 2,530 mm.

What to check before buying

Check the hour meter against the service records — a replaced instrument is the most common gap.
Compare the data plate and chassis number with the papers.
Check the weights in the papers against the figures here — attachments change them.
Shift the gearbox cold and warm — jumps only show up at temperature.
Load the hydraulics and watch for sag.
Ask about parts availability for this build year — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →

Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 17 individual figures for this model. They come from 2 recorded sources; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →