Technical register for agricultural, construction and commercial machinery · sourced data
Start › Electric motors › Sumitomo › N-225S

Sumitomo N-225S

Series: Other models

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Sumitomo Corporation N-225S is a three-phase induction motor built by Sumitomo Corporation. The rated output is 55 kW. The motor is four-pole, which at 50 Hz gives a synchronous speed of 1,500 rpm. The rated voltage is 415 V. The housing is frame size 225 S in foot-mounted form. The protection class is IP55. The efficiency is 95.1 per cent at full load, 95.1 per cent at 75 per cent load and 94.2 per cent at half load. The mounting arrangement to IEC 60034-7 is B5. Stated countries of manufacture: Japan and Vietnam. The figures come from the Australian MEPS register under the GEMS Determination 2019; measured to IEC 60034-2-1 (Edition 2.0). Rated output across the Sumitomo Corporation range ranges from 0.75 to 55 kW; the N-225S sits at the top of that range with 55 kW. Its immediate neighbours are the FA-180L below it with 30 kW. 13 Sumitomo Corporation models are on record. The model is listed under Electric motors. 21 verified figures from 1 source are on file.

Sumitomo – other models: the collective page of MEPS-registered three-phase motors made in Japan and Vietnam outside the named ranges, FA, GA, N and VA series, frame sizes 80 to 225, 0.75 to 55 kW

This page gathers the Sumitomo three-phase motors the Australian energy-efficiency register could not assign to a named range. Model designations split into four ranges – FA, GA, N and VA – each followed by the IEC frame size and a letter for the build length (S, M, L); all 13 motors are four-pole. Manufacture is mostly in Japan, alongside Vietnam and a combination of both countries.

Read on 3 more paragraphs

The register lists here 13 versions with 0.75 to 55 kW, exclusively four-pole, full-load efficiencies from 83.7 to 95.1% and at 75% load from 82.8 to 95.1%. Frame sizes run from 80 to 225, protection is IP54 and IP55, voltage is uniformly 415 V, mounting form is consistently B5. Testing followed the 2019 GEMS determination, mostly with test method B; of 13 motors, 3 reach the 2005 High Efficiency Level and 2 the 2018 level, the remaining 8 stay unclassified.

Sumitomo is one of the large Japanese industrial groups with its own drive-technology division; the four-pole standard motors on this page chiefly complement gear motors and planetary drives there into complete drive solutions for conveyors, agitators and packaging machinery.

When buying used, bearing condition and a checked insulation resistance of the winding, the condition of shaft, key and fan cover, a legible nameplate with range, frame size and efficiency class, and on the B5 flange motors the condition of the centring spigot on the bearing shield all matter; spares run through Sumitomo's distribution.

Sources: Kennwerte der Modelle Sumitomo (weitere Modelle, MEPS-Registrierungen)

Technical data

Engine

Rated output55 kWcorrect

Electrical data

Rated voltage415 Vcorrect
Number of poles4correct
Protection classIP55correct
Frame size225 S (foot)correct
Mounting (IEC 60034-7)B5correct
Efficiency at full load95.1 %correct
Efficiency at 75 % load95.1 %correct
Efficiency at half load94.2 %correct

Origin and approval

Country of manufactureJapan, Vietnamcorrect

Other data

Standard appliedGreenhouse and Energy Minimum Standards (Three Phase Electric Motors) Determination 2019correct
Test methodIEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the Sumitomo N-225S have?

The Sumitomo N-225S delivers 55 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 21 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: [1]

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare