Start › Electric motors › Neri Motori › Other models › 2 pole

Neri Motori 2 pole

Series: Other models

The photo shows the H132M2 MULT. 7.5Kw from the same series. Source: neri-motori-info.ru

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Neri Motori 2 pole is a three-phase induction motor built by Neri Motori. The rated output is 1.1 kW. The motor is two-pole, which at 50 Hz gives a synchronous speed of 3,000 rpm. The housing is frame size 80 M in foot-mounted form. The protection class is IP55. The efficiency is 82.2 per cent at full load, 79.5 per cent at 75 per cent load and 75.3 per cent at half load. The mounting arrangement to IEC 60034-7 is B3. The motor is built in Italy. The data is based on the Australian MEPS registration under standard AS/NZS 1359.5:2004; measured to IEC 60034-2-1 (Edition 2.0). Rated output across the Neri Motori range ranges from 0.75 to 7.5 kW; the 2 pole sits at the bottom of that range with 1.1 kW. Its immediate neighbours are the 4 pole below it with 0.75 kW and the H132M2 MULT. 7.5Kw above it with 7.5 kW. 3 Neri Motori models are on record.

Neri Motori – other models: the collective page of MEPS-registered three-phase motors outside the named ranges, an Italian maker from Bologna, 0.75 to 7.5 kW, two- to four-pole, IP55

This page gathers the Neri Motori three-phase motors the Australian energy-efficiency register could not assign to a named range. Neri Motori is an Italian maker of electric motors based in Bologna; the register records two- and four-pole versions as well as the H132M2 MULT. type at 7.5 kW.

Read on 3 more paragraphs

The register lists here 3 versions with 0.75 to 7.5 kW, two- to four-pole, with full-load efficiencies from 81.8 to 89.6% and at 75% load from 79.5 to 84.3%. Protection is uniformly IP55, frame size runs from 80 to 132, mounting code uniformly B3. Italy is recorded as the manufacturing country; testing followed AS/NZS 1359.5:2004 with test methods B and A; none of the three motors reaches a High Efficiency classification under GEMS.

Motors in this span from under 1 to 7.5 kW with frame sizes from 80 to 132 cover a wide field from small auxiliary drives to pumps in commercial use; registration under the Australian GEMS standard shows that Neri Motori certifies its range for the Australian market too.

When buying used or replacing, what matters is bearing condition and a checked insulation resistance of the winding, visible overheating marks on the terminal box and fan cover, the condition of shaft and key, and a legible nameplate with frame size and pole count; anyone wanting to run the motor on a variable-speed drive should check its inverter suitability beforehand. Spares run through Neri Motori's sales channel.

Sources: SpecCodex register, model data: Neri Motori (weitere Modelle, MEPS-Registrierungen)

Technical data

Engine

Rated output	1.1 kWcorrect

Electrical data

Rated voltage	230/380/400/415 Vcorrect
Number of poles	2correct
Protection class	IP55correct
Frame size	80 M (foot)correct
Mounting (IEC 60034-7)	B3correct
Efficiency at full load	82.2 %correct
Efficiency at 75 % load	79.5 %correct
Efficiency at half load	75.3 %correct

Origin and approval

Country of manufacture	Italycorrect

Other data

Standard applied	AS/NZS 1359.5:2004correct
Test method	IEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the Neri Motori 2 pole have?

The Neri Motori 2 pole delivers 1.1 kW.

What to check before buying

Match the data plate against the order: frame size, mounting and rating have to agree.
Check the ingress rating against the installation site — outdoors or in dust the demands differ.
Hold the mounting form and dimensions against the existing seat before ordering.
The pole count sets the speed — when replacing an older unit, compare this first.
For used units, ask about winding condition and bearing play.
Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →

Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 22 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →