Technical register for agricultural, construction and commercial machinery · sourced data
Start › Electric motors › Maxeff Motors › Other models › NMST250M-4/MAXEFF

Maxeff Motors NMST250M-4/MAXEFF

Series: Other models

Source: xueqiu.com

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Maxeff Motors NMST250M-4/MAXEFF is a three-phase induction motor from the Maxeff Motors range. The rated output is 75 kW. The motor is four-pole, which at 50 Hz gives a synchronous speed of 1,500 rpm. The housing is frame size 250 M in foot-mounted form. The protection class is IP55. The efficiency is 93.4 per cent at full load, 94 per cent at 75 per cent load and 93.4 per cent at half load. The motor weighs 520 kg. At full load it delivers 484 Nm. The mounting arrangement to IEC 60034-7 is B3. The motor is built in Turkey. The data is based on the Australian MEPS registration under the GEMS Determination 2019; measured to IEC 60034-2-1 (Edition 2.0). Rated output within this group ranges from 0.18 to 1,119 kW; the NMST250M-4/MAXEFF sits at the bottom of that range with 75 kW. Its immediate neighbours are the DVE280S below it with 74 kW and the M3AA/BP 225 SMD 2 above it with 80 kW.

MaxEff Motors – other models: the collective page of MEPS-registered three-phase motors from Turkey outside the named ranges, frame size 250, 75 kW, four-pole, efficiencies up to 95.2%

This page gathers the MaxEff Motors three-phase motors the Australian energy-efficiency register could not assign to a named range. The designations recorded in the register, NMST250/4-350 and NMST250M-4/MAXEFF, carry the IEC frame size 250 and the pole count 4 directly in the name, supplemented by an output or build-length marker.

Read on 3 more paragraphs

The register lists here 2 versions, each with 75 kW rated output, both four-pole, for a 380/400 V or 380/400/415 V supply, with full-load efficiencies from 93.4 to 95.2% and at 75% load from 94 to 95.6%. Protection is IP55, the mounting code B3 (foot type); testing followed AS/NZS 1359.5:2004 with test method B or the 2019 GEMS determination with test method A. One of the two versions reaches the 2005 High Efficiency Level, corresponding roughly to the IE2 class. Manufacturing takes place in Turkey.

With efficiencies of up to 95.2% at full load, these motors sit at the upper end of what four-pole three-phase motors of this power class achieve; such high-efficiency 75 kW motors typically drive large pumps, compressors and fans in industry, where energy consumption over the service life clearly exceeds the purchase cost.

When buying used, bearing condition and a checked insulation resistance of the winding, the condition of shaft, key and fan cover, and a legible nameplate with frame size, pole count and efficiency class matter. Spares run through MaxEff's Turkish distribution.

Sources: SpecCodex register, model data: MaxEff Motors (weitere Modelle, MEPS-Registrierungen)

Technical data

Engine

Rated output75 kWcorrect

Dimensions and weights

Weight520 kgcorrect

Electrical data

Rated voltage380/400 Vcorrect
Number of poles4correct
Protection classIP55correct
Frame size250 M (foot)correct
Mounting (IEC 60034-7)B3correct
Efficiency at full load93.4 %correct
Efficiency at 75 % load94 %correct
Efficiency at half load93.4 %correct

Origin and approval

Country of manufactureTurkeycorrect

Other data

Standard appliedGreenhouse and Energy Minimum Standards (Three Phase Electric Motors) Determination 2019correct
Test methodIEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the Maxeff Motors NMST250M-4/MAXEFF have?

The Maxeff Motors NMST250M-4/MAXEFF delivers 75 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 25 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: Energy Rating — Australian government equipment register (retrieved August 2026) · How we check the data

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare