K+g Tec GmbH Zerbst SKA 8,0-E
Built: 2013 · Series: Other models
More machines from model year 2013
Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required
K+g Tec GmbH Zerbst SKA 8,0-E: EU class O3 trailer with a gross weight of 7,880 kg, a length of 7.25 m, a 4,750 mm wheelbase and a payload of about 4,520 kg
With a gross weight of 7,880 kg, the SKA 8,0-E sits in EU trailer class O3, the band between 3.5 and 10 tonnes. Trailers in this class are a common middle ground between the small, unbraked class O2 models and the heavy semi-trailers of class O4, and are towed by medium trucks and light tractor units.
Read on 3 more paragraphs
With an unladen weight of 3,360 kg, the trailer carries a payload of around 4,520 kg, more than its own weight. The load area is 7.25 m long and 2.55 m wide, and the wheelbase is 4,750 mm. This ratio of unladen weight to payload is typical of a light build optimised for load volume rather than for its own weight.
From class O3 upward, EU rules require an air brake rather than a simple overrun brake, so the towing vehicle needs a matching air coupling. Depending on the towing vehicle, licence category C1E or BE is sufficient to drive a combination like this, provided the permissible gross train weight stays within the relevant limits. Trailers in this weight class also need rear underrun protection under UN/ECE Regulation R58, intended to reduce the severity of collisions where a car runs into the back of the trailer.
When buying a used trailer of this size, it is worth checking the load area for deformation and corrosion spots, the brake lines for leaks, and the coupling for wear. The lighting system, the electrical connectors, and whether the chassis number matches the registration papers are further points that can be checked concretely. The rear underrun protection should additionally be checked for secure mounting and any deformation.
Sources: SpecCodex-Register: Kennwerte des Modells SKA 8,0-E
Technical data
Dimensions and weights
| Length | 7,250 mmcorrect |
|---|---|
| Width | 2,550 mmcorrect |
| Wheelbase | 4,750 mmcorrect |
| Unladen weight | 3,360 kgcorrect |
| Gross vehicle weight | 7,880 kgcorrect |
Drivetrain and chassis
| Top speed | 100 km/hcorrect |
|---|
Frequently asked questions
How much does the K+g Tec GmbH Zerbst SKA 8,0-E weigh?
The unladen weight is 3,360 kg.
What is the gross vehicle weight of the K+g Tec GmbH Zerbst SKA 8,0-E?
7,880 kg.
Up to what speed is the K+g Tec GmbH Zerbst SKA 8,0-E approved?
Approved up to 100 km/h.
What are the dimensions of the K+g Tec GmbH Zerbst SKA 8,0-E?
7,250 mm × 2,550 mm.
When was the K+g Tec GmbH Zerbst SKA 8,0-E built?
Production years: 2013.
What to check before buying
- Search the frame and welds at the axle mounts — that is where cracks start.
- Check the brakes and the last inspection in the papers.
- Work the gross weight against the towing vehicle before buying.
- Compare the chassis number with the papers.
- Look at the floor, cover or body from the inside — rust does not show from outside.
A general list for this type of machine — no substitute for an inspection or an appraiser.
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
We ask the suppliers and come back with price and lead time.
Request spare parts →
This page carries 8 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.
The technical data on this page comes from official vehicle registration records (RDW/Traficom), not from the manufacturer.
Missing a figure you were looking for? Report it →
Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →
Sources: RDW — Dutch national vehicle register (retrieved August 2026) · How we check the data
Trailer in 3D section
Turn the model, look inside and click an assembly — each one is explained.
