John Deere 7510
Series: Other models
Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required
The John Deere 7510 is a tractor model from the John Deere range of agricultural machines. It belongs to the tractor series and was produced in the specified production period. The machine is equipped with a 6‑cylinder engine of 6 788 cm³ displacement delivering 135 hp (99.4 kW) at a rated speed of 2 100 rpm and a torque of 535 Nm. Overall dimensions are 4 435 mm in length, 2 808 mm in width and 2 880 mm in height. Transmission options are 16V/16R or 20V/20R, the fuel tank holds 189 l and the pump shaft speed is 540/1000 rpm. The lift category is Cat II/III.
A power output of 135 hp enables the tractor to pull heavy implements and work on large field areas, while the 535 Nm torque provides strong acceleration and the ability to handle high loads. The relatively large chassis, 4 435 mm long and 2 808 mm wide, offers stability and a low ground pressure, beneficial on soft ground. The 189 l fuel capacity allows extended operation without frequent refuelling, and the versatile gearbox with up to 20 forward and reverse gears permits fine speed adjustment to match varying field conditions.
A tractor of this size and power class is typically suited for medium to large farms that perform extensive field tasks such as plowing, seeding and harvesting. The combination of high power, robust construction and a wide‑range transmission enables it to manage both heavy pulling duties and precise field work. The Cat II/III lift rating also makes it appropriate for use with heavy attachments like mulchers or bale presses.
John Deere – other models: the collective page of tractors outside the named ranges, from the two-cylinders and the 10 series (1020, 2020) through the 40s and 50s from Mannheim to the 1023E, 3038E and 9RX, 6 to 468 kW
This page gathers the John Deere tractors the register could not assign to a named range – from the successors of the two-cylinders through the European ranges from Mannheim to the compact tractors from Augusta, Georgia. John Deere, founded in 1837 as a plough smithy in Illinois, has built tractors in Waterloo, Iowa, since 1918 and since 1956, with the takeover of Lanz, in Mannheim, today the largest tractor plant outside North America. The type logic: the 10 series of 1960 (1010 to 5010) brought the four- and six-cylinders after the two-cylinder era, the 20s, 30s and 40s (1020, 2130, 2140) the Mannheim generations of the 1960s to 1980s, in which the first digit gives the size and the last ones the generation; the 50s (1750 to 3650) followed in 1986, the 55s and 6000s in 1992. Since 1992 the first digit marks the range (1 to 9) and the following ones the power – 1023E as a 1 series compact with 23 hp, 3038E as a 3 series with 38 hp, 5075E as a 5 series with 75 hp – E, M and R the equipment lines from basic to premium. The engines are Deere's own PowerTech range in the big, Yanmar in the compact and Lombardini in the smallest tractors.
Read on 3 more paragraphs
The register lists here 925 versions with 6.3 to 468.3 kW from one- to six-cylinders of 341 to 13,503 cm³, PTO outputs from 17 to 365 hp, lift capacities from 309 to 13,494 kg, unladen weights from 363 to 20,371 kg, lengths from 2,362 to 6,880 mm and widths from 1,194 to 3,952 mm.
John Deere has been the world's largest farm-equipment maker for decades; the Mannheim 6 series is Europe's best-selling tractor, the compacts from Augusta North America's.
On used tractors, originality and engine condition count on classics, transmission (Synchron or Power-Synchron) and hydraulics on the Mannheim 40s and 50s, and on the E, M and R models operating hours, transmission (PowrQuad, AutoQuad, AutoPowr), electronics and exhaust aftertreatment; parts run through the Deere network.
Sources: SpecCodex register, model data: John Deere (weitere Modelle), John Deere (manufacturer)
Technical data
Engine
| Power | 135 hp (99.4 kW)correct |
|---|---|
| Rated speed | 2,100 rpmcorrect |
| Torque | 535 Nmcorrect |
| Cylinders | 6correct |
| Displacement | 6,788 cm³correct |
Dimensions and weights
| Length | 4,435 mmcorrect |
|---|---|
| Width | 2,808 mmcorrect |
| Height | 2,880 mmcorrect |
Drivetrain and chassis
| Gearbox | 16V/16R or 20V/20Rcorrect |
|---|
Working data
| Fuel tank capacity | 189 lcorrect |
|---|
Other data
| Linkage category | Cat II/IIIcorrect |
|---|---|
| PTO speed | 540/1000 rpmcorrect |
Frequently asked questions
How much power does the John Deere 7510 have?
The John Deere 7510 delivers 135 hp.
What engine does the John Deere 7510 have?
6 cylinders, 6,788 cm³ displacement.
What are the dimensions of the John Deere 7510?
4,435 mm × 2,808 mm × 2,880 mm.
What to check before buying
- Check the hour meter against the service records — a replaced instrument is the most common gap.
- Compare the data plate and chassis number with the papers.
- Shift the gearbox cold and warm — jumps only show up at temperature.
- Load the hydraulics and watch for sag.
- Ask about parts availability for this build year — the running costs hang on it.
A general list for this type of machine — no substitute for an inspection or an appraiser.
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
We ask the suppliers and come back with price and lead time.
Request spare parts →
This page carries 13 individual figures for this model. They come from 2 recorded sources; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.
Missing a figure you were looking for? Report it →
Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →
Other models in this series
Sources: Wikipedia (CC BY-SA 4.0) (retrieved August 2026) · Wikibooks Traktorenlexikon (CC BY-SA 4.0) (retrieved September 2026) · Values adopted and presented in our own form; changes from the source are possible. · How we check the data
Tractor in 3D section
Turn the model, look inside and click an assembly — each one is explained.
