Technical register for agricultural, construction and commercial machinery · sourced data
Scanner Parts Sign in
Start › Electric motors › Intem › EG-112M-4

Intem EG-112M-4

Series: Other models

The photo shows the EG-315L2-2 from the same series. Source: https://www.weg.net/catalog/weg/CI/en/Electric-Motors/Low-Vo

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The EG-112M-4 from Intem is a three-phase induction motor. The rated output is 4 kW. The motor is four-pole, which at 50 Hz gives a synchronous speed of 1,500 rpm. The rated voltage is 415 V. The housing is frame size 112 M in foot-mounted form. The protection class is IP55. The efficiency is 84.2 per cent at full load, 84.1 per cent at 75 per cent load and 82.5 per cent at half load. The motor weighs 43 kg. At full load it delivers 26.34 Nm. The motor is built in China. The data is based on the Australian MEPS registration under standard AS/NZS 1359.5:2000 (Legacy); measured to AS 1359.102.1:1997. Rated output across the Intem range ranges from 0.75 to 200 kW; the EG-112M-4 sits at the bottom of that range with 4 kW. Its immediate neighbours are the EGA-132S-6 below it with 3 kW and the EG-132M2-6 above it with 5.5 kW. 103 Intem models are on record.

Intem – other models: the collective page of MEPS-registered three-phase motors outside the named ranges, frame sizes 80 to 315, 0.75 to 200 kW, 2- to 8-pole, 415 V, IP55 throughout

This page gathers the three-phase motors carried in the Australian energy-efficiency register under the Intem brand, which the register does not assign to a named range. The 415 V rating matches the Australian supply grid, not the European 400 V standard. The type designations follow the scheme EG-frame size-pole count, sometimes with an extra digit for a winding variant, e.g. EG-100L-2 or EG-160M1-2; the further meaning of the extra digits cannot be reliably established from the dump.

Read on 3 more paragraphs

The register lists here 103 versions with 0.75 to 200 kW, two- to eight-pole, all rated for 415 V. Full-load efficiencies run between 72.6 and 95.42%, with the 75%-load figures in a similar range, reaching close to 95% in places. All 103 motors are built to protection rating IP55, frame sizes run from 80 to 315 under IEC, manufactured throughout in China and tested under the older Legacy standard AS/NZS 1359.5:2000 with test method B. None of the 103 motors is classified under the Australian High Efficiency Level. Mounting codes are dominated by the broad foot form B3/B5/B6/B7/B8/V1/V3/V5/V6, alongside an even wider combination with B14, B35 and vertical forms V15 to V36, and the plain foot form B3/V1.

The page thus covers a broad IEC standard-motor programme of the kind used in industry for pumps, fans, conveyors and compressors; consistent manufacture in China and the uniform 415 V supply point to a catalogue programme reaching the Australia-Pacific market through various distributors.

When buying used, what matters is bearing condition and a checked insulation resistance of the winding, visible overheating marks on the terminal box and fan cover, the condition of shaft and key, and a legible nameplate with frame size, pole count and efficiency class; since none of the motors carries a High Efficiency Level certification, for continuous duty it is worth comparing against IE2/IE3 alternatives. Spares depend on the distribution channel.

Sources: SpecCodex register, model data: Intem, Zulassungsdaten GEMS/MEPS (Australien)

Technical data

Engine

Rated output4 kWcorrect

Dimensions and weights

Weight43 kgcorrect

Electrical data

Rated voltage415 Vcorrect
Number of poles4correct
Protection classIP55correct
Frame size112 M (foot)correct
Mounting (IEC 60034-7)B3, B5, B6, B7, B8, B14, B35, V1, V3, V5, V6, V15, V18, V19, V36correct
Efficiency at full load84.24 %correct
Efficiency at 75 % load84.14 %correct
Efficiency at half load82.54 %correct

Origin and approval

Country of manufactureChinacorrect

Other data

Standard appliedAS/NZS 1359.5:2000 (Legacy)correct
Test methodAS 1359.102.1:1997correct

Frequently asked questions

How much power does the Intem EG-112M-4 have?

The Intem EG-112M-4 delivers 4 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 24 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

EG-100L-2

EG-100L-6

EG-100L1-4

EG-100L2-4

EG-112M-2

EG-112M-6

EG-132M-4

EG-132M-8

EG-132M1-6

EG-132M2-6

EG-132S-4

EG-132S-6

Sources: [1]

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare