Technical register for agricultural, construction and commercial machinery · sourced data
Start › LPG forklifts › Hyster › H 2.50 XL

Hyster H 2.50 XL

Series: Hyster Treibgasstapler

The photo shows the H7.0FT-L from the same series. Source: https://www.lectura-specs.com/en/model/forklifts/lpg-forklif

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

As a forklift truck, the Hyster H 2.50 XL belongs to the Hyster Treibgasstapler series. The Standard mast lifts to 3.30 m; capacity is 2,500 kg.

Hyster H7.0FT-L: LPG forklift with a triplex mast, a load capacity of 7,000 kilograms and a lift height of 4,705 millimetres for use indoors and outdoors

Hyster is an American manufacturer of forklift trucks. The H7.0FT-L belongs to the group of LPG forklifts, materials-handling equipment whose combustion engine runs on liquefied petroleum gas instead of diesel or petrol.

Read on 3 more paragraphs

The H7.0FT-L lifts a load of 7,000 kilograms to a height of 4,705 millimetres. The lifting motion runs through a triplex mast, a three-stage mast that stays compact when retracted and only extends to its full height once the load is raised.

LPG forklifts such as the H7.0FT-L burn their fuel more cleanly than diesel-powered trucks, so with adequate ventilation they can also be used inside enclosed buildings, while outdoors they work just as they do indoors. The stated load capacity of 7,000 kilograms applies at the load centre set out under EU standards, usually 500 millimetres for forklifts, and it falls as lift height increases or the load's centre of gravity shifts.

When buying second-hand, the LPG fuel system deserves particular attention: lines, threaded fittings and the tank-change mechanism should be checked for leaks and the condition of the seals. The triplex mast shows wear on its guide rails and lifting chains, which shows up as stretching, and the lift cylinders should be free of oil traces. At a load capacity of seven tonnes, it is also worth checking the tyres and axles, which carry particular strain under that load.

Sources: SpecCodex-Register: Kennwerte des Modells Hyster H7.0FT-L, Hyster

Technical data

Working data

Lifting capacity2,500 kgcorrect
Lift height3,300 mmcorrect
Mast typestandardcorrect

Frequently asked questions

What is the load capacity of the Hyster H 2.50 XL?

Load capacity is 2,500 kg, lift height 3,300 mm.

What to check before buying

  • Check the hour meter against the service records — a replaced instrument is the most common gap.
  • Compare the data plate and chassis number with the papers.
  • Ask about parts availability for this build year — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 3 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: [1]

Forklift in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare