EMT Y2 HE 160M4 – specifications
Series: Y2
The EMT Y2 HE 160M4 is a three-phase induction motor from the Y2 series. The rated output is 11 kW. The motor is four-pole, which at 50 Hz gives a synchronous speed of 1,500 rpm. The rated voltage is 400 V. The housing is frame size 160 M in foot-mounted form. The protection class is IP55 and IP56. The efficiency is 91 per cent at full load, 91.3 per cent at 75 per cent load and 90.6 per cent at half load. The motor weighs 114 kg. At full load it delivers 71.7 Nm. Mounting arrangements to IEC 60034-7: B3, B5, B14, B34, B35, V1, V3 and V5. The motor is built in China. The figures come from the Australian MEPS register under standard AS/NZS 1359.5:2004; measured to IEC 60034-2-1 (Edition 2.0). The Y2 series covers 42 models. Rated output within it ranges from 0.75 to 75 kW; the Y2 HE 160M4 sits at the bottom of that range with 11 kW. Its immediate neighbours are the Y2 HE 160M6 below it with 7.5 kW and the Y2 HE 160L4 above it with 15 kW. 274 EMT models across 5 series are on record.
Build year not documented · Data origin: Official register · sources
Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required
EMT Y2 – other models: the collective page of MEPS-registered three-phase motors built to the Chinese Y2 standard-motor scheme outside the named ranges, frame sizes 80 to 280, 0.75 to 75 kW, 2- to 8-pole
This page gathers the three-phase motors from the supplier EMT that the Australian energy-efficiency register could not assign to a named range. The model designations consistently follow the Y2 range scheme – Y2 200L4, Y2 AHE 112M2, Y2 HE 100L14 – a standard-motor design for three-phase induction motors widespread in China that replaced the older Y range. The AHE and HE suffixes within the model designation mark separate range variants; their exact technical meaning cannot be reliably reconstructed from the dump alone.
Read on 3 more paragraphs
The register lists here 42 versions with 0.75 to 75 kW, two- to eight-pole, full-load efficiencies from 77.5 to 95% and at 75% load from 76.6 to 95.2%. Frame sizes run from 80 to 280, protection is IP55/IP56 for practically all 42 motors, and the mounting codes are uniformly set to the full B3, B5, B14, B34, B35, V1, V3, V5 set. China alone is recorded as the manufacturing country. Testing mostly followed AS/NZS 1359.5:2004 and the 2019 GEMS determination, with test method B for the large majority; only 5 of the 42 motors reach the 2005 High Efficiency Level, 37 remain unclassified.
The Y2 range is built by numerous Chinese makers in near-identical form and forms the backbone there of value-oriented standard-motor demand for pumps, fans, compressors and conveying plant; EMT appears here as one of the suppliers registering this scheme under its own brand name.
When buying used, what matters is bearing condition and a checked insulation resistance of the winding, the visible build quality of the terminal box and fan cover, the condition of shaft and key, and a legible nameplate with frame size, pole count and, where present, efficiency class; since only a small share of the models carry a High Efficiency classification, inverter suitability should be checked case by case. Spares run through the relevant EMT distribution channel.
Sources: SpecCodex register, model data: EMT Y2 (weitere Modelle, MEPS-Registrierungen)
Technical data
Engine
| Rated output | 11 kWcorrect |
|---|
Dimensions and weights
| Weight | 114 kgcorrect |
|---|
Electrical data
| Rated voltage | 400 Vcorrect |
|---|---|
| Number of poles | 4correct |
| Protection class | IP55, IP56correct |
| Frame size | 160 M (foot)correct |
| Mounting (IEC 60034-7) | B3, B5, B14, B34, B35, V1, V3, V5correct |
| Efficiency at full load | 91 %correct |
| Efficiency at 75 % load | 91.3 %correct |
| Efficiency at half load | 90.6 %correct |
Origin and approval
| Country of manufacture | Chinacorrect |
|---|
Other data
| Standard applied | AS/NZS 1359.5:2004correct |
|---|---|
| Test method | IEC 60034-2-1 (Edition 2.0)correct |
Frequently asked questions
What to check before buying
- Match the data plate against the order: frame size, mounting and rating have to agree.
- Check the ingress rating against the installation site — outdoors or in dust the demands differ.
- Hold the mounting form and dimensions against the existing seat before ordering.
- The pole count sets the speed — when replacing an older unit, compare this first.
- For used units, ask about winding condition and bearing play.
- Ask about parts availability for this series — the running costs hang on it.
A general list for this type of machine — no substitute for an inspection or an appraiser.
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
We ask the suppliers and come back with price and lead time.
Request spare parts →
This page carries 24 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.
Are you the manufacturer or a dealer of this machine? Check the data and add missing figures — we mark your correction as manufacturer or dealer information.
Check and complete the data →Missing a figure you were looking for? Report it →
Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →
Other models in this series
Y2 200L4
Y2 200L6
Y2 200LX2
Y2 200LX6
Y2 AHE 100L2
Y2 AHE 100L6
Y2 AHE 112M2
Y2 AHE 112M6
Y2 AHE 132M4
Y2 AHE 132S12
Y2 AHE 132S22
Y2 AHE 8022
Sources: Energy Rating — Australian government equipment register (retrieved August 2026) · Data sources and cross-checks
Electric motor in 3D section
Turn the model, look inside and click an assembly — each one is explained.