Technical register for agricultural, construction and commercial machinery · sourced data
Start › Trucks › Bristol › Other models › 2-AXLE-RIGID BODY

Bristol 2-AXLE-RIGID BODY

Built: 1965-1980 · Series: Other models

More machines from model year 1965

The photo shows the 4D6G from the same series. Source: en.wikipedia.org

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Bristol 2-AXLE-RIGID BODY is a vehicle built by Bristol. Production: 1965-1980. The engine has 6 cylinders, with a displacement of 10,500 cm³. The vehicle is 9,300 mm long and 2,500 mm wide. The unladen weight is 9,822 kg. The wheelbase measures 5,850 mm. Top speed is 90 km/h. The gross vehicle weight is 15,621 kg. The vehicle runs on 4 wheels. Unladen weight across the Bristol range ranges from 6,177 to 10,765 kg; the 2-AXLE-RIGID BODY sits in the upper part of that range with 9,822 kg. Its immediate neighbours are the VRT below it with 9,805 kg and the BUS above it with 10,765 kg. Gross vehicle weight across the Bristol range ranges from 8,100 to 16,266 kg; here the 2-AXLE-RIGID BODY sits at the top of that range with 15,621 kg. 19 Bristol models across 2 series are on record.

Bristol – other models: the collective page for the British bus maker active until 1983, from the K chassis through the Lodekka range (FS, FLF) to the rear-engined double-decker VR/VRT, five- and six-cylinder

This page gathers vehicles from Bristol Commercial Vehicles, the British commercial-vehicle maker that, until 1983, built chiefly bus chassis. The model list in the register ranges from the classic front-engined K chassis (KSW) through the low-height double-decker Lodekka range in the FS and FLF versions to the rear-engined double-deckers VR and VRT, which Bristol built from the mid-1960s onward. Bristol was for a long time closely linked with the bodybuilder Eastern Coach Works (ECW), which produced most of the bodywork, and supplied mainly state-owned British bus operators.

Read on 3 more paragraphs

The register lists 18 versions here with five- and six-cylinder engines, unladen weights from 6,177 to 10,765 kg, gross weights from 8,100 to 16,266 kg and widths from 2,270 to 2,530 mm; for part of the models, displacements of 5,200 to 10,500 cc and lengths of 8,220 to 9,400 mm.

Bristol vehicles shaped bus travel across much of Britain for decades, especially within the state-owned Tilling Group network; the Lodekka range was known for its especially low overall height, allowing passage under low bridges, while the VR and VRT ran as rear-engined double-deckers in service well into the 1980s.

On surviving Bristol vehicles, the condition of the frame and bodywork, especially on ECW-built bodies, the condition of the commonly fitted Gardner diesel engines, the gearbox and braking system, and on double-deckers the structural soundness of the upper deck all count; spare parts are today obtained mostly through vintage-bus clubs and specialists.

Sources: SpecCodex register, model data: Bristol (weitere Modelle)

Technical data

Engine

Cylinders6correct
Displacement10,500 cm³correct

Dimensions and weights

Length9,300 mmcorrect
Width2,500 mmcorrect
Wheelbase5,850 mmcorrect
Unladen weight9,822 kgcorrect
Gross vehicle weight15,621 kgcorrect

Drivetrain and chassis

Wheels4correct
Top speed90 km/hcorrect

Frequently asked questions

How much does the Bristol 2-AXLE-RIGID BODY weigh?

The unladen weight is 9,822 kg.

What is the gross vehicle weight of the Bristol 2-AXLE-RIGID BODY?

15,621 kg.

What engine does the Bristol 2-AXLE-RIGID BODY have?

6 cylinders, 10,500 cm³ displacement.

How fast does the Bristol 2-AXLE-RIGID BODY go?

Top speed is 90 km/h.

What are the dimensions of the Bristol 2-AXLE-RIGID BODY?

9,300 mm × 2,500 mm.

When was the Bristol 2-AXLE-RIGID BODY built?

Production years: 1965-1980.

What to check before buying

  • Check the hour meter against the service records — a replaced instrument is the most common gap.
  • Compare the data plate and chassis number with the papers.
  • Check the weights in the papers against the figures here — attachments change them.
  • Ask about parts availability for this build year — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 11 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

The technical data on this page comes from official vehicle registration records (RDW/Traficom), not from the manufacturer.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: RDW — Dutch national vehicle register (retrieved August 2026) · How we check the data

Truck in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare