Technical register for agricultural, construction and commercial machinery · sourced data

Tadano ATF50G-3

Series: Tadano All Terrain Crane

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

With the ATF50G-3, Tadano offers a model from the Tadano All Terrain Crane series. The engine delivers 330.5 hp (243.1 kW), with a displacement of 7,200.5 cm³. Torque is 1,300.1 Nm. Rated speed is 2,200 rpm. The unladen weight is 36,001.6 kg. The gearbox has 12 forward gears. There are also 2 reverse gears. Maximum torque is reached at 1,600 rpm. The electrical system runs on 24 V. Tyre size: 14,00R25. The Tadano All Terrain Crane series covers 20 models. Rated output within it ranges from 176.4 to 633.7 hp; the ATF50G-3 sits in the lower part of that range with 330.5 hp. Its immediate neighbours are the RTF50-4 below it with 330.4 hp and the ATF-650XL-2 above it with 353.8 hp. 111 Tadano models across 5 series are on record. The model is listed under Cranes & access platforms. 12 verified figures from 1 source are on file.

Tadano all-terrain cranes ATF 30 to ATF 400G-6 – Faun heritage from Lauf an der Pegnitz: the type logic capacity-G-axles, 130 to 324 kW, up to 400 t

The ATF cranes are the European face of Tadano: ATF stands for All Terrain Faun, because the cranes are built at the Lauf an der Pegnitz plant near Nuremberg, which Tadano took over in 1990 from the Franconian commercial-vehicle maker Faun. Since 2019 Demag Mobile Cranes of Zweibrücken has also belonged to Tadano; the two programmes were merged and younger models carry the AC designation. The register shows the classic ATF generation: the number gives the maximum capacity in tonnes, the G the generation with Tadano control and Euromot engines, the number after the hyphen the axle count – an ATF 100G-4 is a 100-tonner on four axles, an ATF 400G-6 a 400-tonner on six axles. Suffixes such as XL mark the long-boom version, RTF the rough-terrain cranes without road approval and AR the Japanese all-terrain models.

Read on 3 more paragraphs

In the register the models run from 130.5 to 324.4 kW from six- and eight-cylinders of 7,201 to 15,928 cm³, torque from 472 to 1,730 Nm at rated speeds of 1,700 to 2,300 rpm, service weights from 23,950 to 59,999 kg and gross weights from 48,000 to 60,000 kg – the twelve-tonne axle load is the limit European roads set for cranes – lengths from 13,110 to 14,930 mm and widths from 2,750 to 2,800 mm.

All-terrain cranes combine road travel at 80 km/h with off-road capability through all-wheel drive and all-wheel steering; Tadano's hallmarks are the single-engine drive on the medium models (one engine for travel and crane operation) and the Lift Adjuster against load swing.

Used ATFs are traded worldwide. When buying, operating hours separated into travel and crane operation, the condition of telescopic boom and locking, slew ring, outriggers, ropes and the inspection history under the crane rules of the respective country are what count.

Sources: Kennwerte der Modelle Tadano All-Terrain-Krane, Tadano (Hersteller)

Technical data

Engine

Power330.5 hp (243.1 kW)correct
Rated speed2,200 rpmcorrect
Torque1,300.1correct
Speed at max. torque1,600 rpmcorrect
Displacement7,200.5 cm³correct

Dimensions and weights

Unladen weight36,001.6 kgcorrect

Drivetrain and chassis

Gearbox typefull automatic gearboxcorrect
Forward gears12correct
Reverse gears2correct
Tyre size14.00R25correct

Other data

System voltage24 Vcorrect

Where this model stands

Power-to-weight ratio: 6.8 kW/t (243 kW / 36 t)

Stronger than 66% of the mobile & rough terrain cranes in the register — out of 575 models with a stated power figure.

Calculated from the documented figures above — not a rating.

Frequently asked questions

How much power does the Tadano ATF50G-3 have?

The Tadano ATF50G-3 delivers 330 hp.

How much does the Tadano ATF50G-3 weigh?

The unladen weight is 36,002 kg.

What engine does the Tadano ATF50G-3 have?

7,200 cm³ displacement.

What to check before buying

  • Check the hour meter against the service records — a replaced instrument is the most common gap.
  • Compare the data plate and chassis number with the papers.
  • Check the weights in the papers against the figures here — attachments change them.
  • Ask about parts availability for this build year — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 12 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: [1]

Mobile crane in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare