Technical register for agricultural, construction and commercial machinery · sourced data
Start › Electric motors › Wilo › 4210739

Wilo 4210739

Series: Other models

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The Wilo 4210739 is a three-phase induction motor built by Wilo. The rated output is 0.75 kW. The motor is two-pole, which at 50 Hz gives a synchronous speed of 3,000 rpm. The housing is frame size 80 M in foot-mounted form. The protection class is IP54. The efficiency is 81.8 per cent at full load, 82.6 per cent at 75 per cent load and 81.1 per cent at half load. The mounting arrangement to IEC 60034-7 is B35. The motor is built in France. The data is based on the Australian MEPS registration under the GEMS Determination 2019; measured to IEC 60034-2-1 (Edition 2.0). Rated output across the Wilo range ranges from 0.75 to 2.2 kW; the 4210739 sits at the bottom of that range with 0.75 kW. Its immediate neighbours are the 3514167 above it with 0.9 kW. 20 Wilo models are on record. The model is listed under Electric motors. 23 verified figures from 1 source are on file.

Wilo – other models: the collective page of pump motors outside the named ranges, exclusively two-pole, MHI motors and the IL/DL/MVI ranges, 0.75 to 2.2 kW, foot and flange versions

Wilo, founded in 1872 in Dortmund, is one of the large European makers of pumps and pump motors. This page gathers the motors the Australian energy-efficiency register could not assign to a named range, including pure spare-part numbers such as 3514167 and short codes such as MVI, IL, DL and IPL, referring to Wilo's pump ranges (vertical multistage and inline centrifugal pumps). Some motors are recorded in the register explicitly as "MHI Motors … by Wilo France S.A.S." and thus come from Wilo's French subsidiary.

Read on 3 more paragraphs

The register lists here 20 versions with 0.75 to 2.2 kW, uniformly two-pole, full-load efficiencies from 81.8 to 87.5% and at 75% load from 82.6 to 88%. The build form ranges from the flange version frame size 100 to the foot versions 80M and 90M, protection is IP54 and IP55. Testing followed the 2019 GEMS determination and AS/NZS 1359.5:2004, with test methods A, B and 2-1-1B; eleven of the 20 motors carry a documented High Efficiency classification, one of them at the 2005 level.

As pump motors, all 20 versions are two-pole, matched to the typical centrifugal-pump speed of around 2,900 rpm, and cover the lower power segment of heating, cooling and circulation pumps, closely tied to Wilo's own pump range.

When buying used, the condition of the mechanical seal and shaft seal, a checked insulation resistance of the winding, bearing and fan-cover condition, and a legible nameplate with build form, output and voltage rating matter; on the flange motors, the condition of the centring to the pump housing should also be checked. Spares run through the Wilo service network.

Sources: Kennwerte der Modelle Wilo (weitere Modelle, MEPS-Registrierungen), Wilo (Hersteller)

Technical data

Engine

Engine familyMHI Motors (0, 75/80) by Wilo France S.A.S.correct
Engine familiesMHI Motors (0, 75/80) by Wilo France S.A.S.correct
Rated output0.75 kWcorrect

Electrical data

Rated voltage230/400 Vcorrect
Number of poles2correct
Protection classIP54correct
Frame size80 M (foot)correct
Mounting (IEC 60034-7)B35correct
Efficiency at full load81.8 %correct
Efficiency at 75 % load82.6 %correct
Efficiency at half load81.1 %correct

Origin and approval

Country of manufactureFrancecorrect

Other data

Standard appliedGreenhouse and Energy Minimum Standards (Three Phase Electric Motors) Determination 2019correct
Test methodIEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the Wilo 4210739 have?

The Wilo 4210739 delivers 0.8 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 24 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: [1]

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare