Start › Electric motors › WE › 1D280M1-2

WE 1D280M1-2

Series: Other models

The photo shows the 1D225M-4 from the same series. Source: https://www.weg.net/catalog/weg/NE/en/Electric-Motors/Low-Vo

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

The 1D280M1-2 from WE is a three-phase induction motor. The rated output is 90 kW. The motor is two-pole, which at 50 Hz gives a synchronous speed of 3,000 rpm. The housing is frame size 280 M in foot-mounted form. The protection class is IP55. The efficiency is 94.1 per cent at full load, 93.7 per cent at 75 per cent load and 92.2 per cent at half load. The motor is built in China. The figures come from the Australian MEPS register under the GEMS Determination 2012; measured to IEC 60034-2-1 (Edition 2.0). Rated output across the WE range ranges from 0.75 to 160 kW; the 1D280M1-2 sits in the middle of that range with 90 kW. Its immediate neighbours are the 1D315S-6 below it with 75 kW and the 1D280M2-2 above it with 110 kW. 125 WE models are on record. The model is listed under Electric motors. 21 verified figures from 1 source are on file.

Technical data

Engine

Rated output90 kWcorrect

Electrical data

Number of poles2correct
Protection classIP55correct
Frame size280 M (foot)correct
Mounting (IEC 60034-7)B3, B6, B7, B8, V5, V6, B5, V1, V3, B35, V15, V36correct
Efficiency at full load94.1 %correct
Efficiency at 75 % load93.7 %correct
Efficiency at half load92.2 %correct

Origin and approval

Country of manufactureChinacorrect
Standard appliedGreenhouse and Energy Minimum Standards (Three Phase Electric Motors) Determination 2012correct
Test methodIEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the WE 1D280M1-2 have?

The WE 1D280M1-2 delivers 90 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 21 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

1A100L-2

1A100L-6

1A100L1-4

1A100L1-8

1A100L2-4

1A100L2-8

1A112M-4

1A112M-6

1A112M1-2

1A112M1-8

1A112M2-2

1A112M2-8

Sources: [1]

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare