Hanomag R60
Built: 1969-1969 · Series: Other models
More machines from model year 1969
The Hanomag R60 rolled off the line in 1969 as a tractor. It is powered by a four-cylinder engine producing 45 kW.
It runs on diesel; the engine is water-cooled. Within the range, rated power spans from 8.9 to 63 kW; with 45 kW, the R60 sits at the top. Directly alongside are the R450 E with 41 kW below and the R75 Super with 56 kW above.
Hanomag – other models: collective page of German tractors outside the named ranges, from the R types through Granit, Brillant and Perfekt to the articulated Combitrac, 8.8 to 63 kW
This page gathers the Hanomag tractors the register could not assign to a named range, from the early pre-war R types to the post-war Granit, Brillant, Perfekt and Robust ranges and the articulated Combitrac models. Hanomag, the Hannoversche Maschinenbau AG, sold its farm-equipment division to Massey-Ferguson in 1971 and ended tractor production afterwards. The R types such as the R16, R22 or R40 carry roughly their power in hp in the number, while Combitrac models such as the C218 and R440 Combitrac are articulated four-wheel-drive tractors for use in vineyards and orchards.
Read on 3 more paragraphs
The register lists here 56 versions with 8.8 to 63 kW from one- to six-cylinder engines of 511 to 5,702 cm³, unladen weights of 800 to 3,750 kg, lengths of 2,340 to 3,990 mm, widths of 1,480 to 2,110 mm and heights of 1,450 to 2,390 mm; torque ranges from 117 to 265 Nm at rated speeds of 1,100 to 2,600 rpm. Most models run on diesel, a few early types on crude oil, and the R40 Holzgas on a wartime wood-gas unit.
In the 1950s and 1960s Hanomag was among the significant German tractor makers alongside Fendt, Deutz and Eicher, focused on mid-sized yard and field tractors as well as the specialised articulated Combitrac for special crops.
When buying used, on the older R types the cooling system, injection pump and gearbox condition matter, on the Combitrac models additionally the articulation joint and four-wheel-drive bearings; parts are now only found through Hanomag specialists and reproduction-parts makers.
Technical data
Engine
| Engine make | Hanomagcorrect |
|---|---|
| Engine model | D57correct |
| Fuel | dieselcorrect |
| Power | 60 hp (45 kW)correct |
| Cylinders | 4correct |
| Cooling | water-cooledcorrect |
Drivetrain and chassis
| Drive | rear-wheel driveWDcorrect |
|---|---|
| Forward gears | 5correct |
| Reverse gears | 1correct |
Origin and approval
| Plant | Granadero Baigorria, Santa Fe, Argentinacorrect |
|---|
Other data
| Predecessor | not statedcorrect |
|---|---|
| Successor | not statedcorrect |
Frequently asked questions
How much power does the Hanomag R60 have?
The Hanomag R60 delivers 60 hp.
What engine does the Hanomag R60 have?
4 cylinders, Diesel.
When was the Hanomag R60 built?
Production years: 1969.
What to check before buying
- Check the hour meter against the service records — a replaced instrument is the most common gap.
- Compare the data plate and chassis number with the papers.
- Load the hydraulics and watch for sag.
- Ask about parts availability for this build year — the running costs hang on it.
A general list for this type of machine — no substitute for an inspection or an appraiser.
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
We ask the suppliers and come back with price and lead time.
Request spare parts →
This page carries 15 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.
Missing a figure you were looking for? Report it →
Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →
Other models in this series
36/40 Industrial
AGR 38
Barreiros R545
Brillant 600
Brillant 601L
Brillant 700
Brillant 701
C 218 Combitrac
C 224 Combitrac
Granit 500E
Granit R 332
Greif C 115
Sources: [1]
Tractor in 3D section
Turn the model, look inside and click an assembly — each one is explained.