Technical register for agricultural, construction and commercial machinery · sourced data
StartElectric motorsABB › M3BP 90SLB2

ABB M3BP 90SLB2

Series: M3BP

Not the right version? The data comes from vehicle registers holding many near-identical versions side by side. Photograph the data plate — we read make and type from it. Open the scanner e-mail address required

ABB lists the M3BP 90SLB2 as a three-phase induction motor. The rated output is 1.5 kW. The motor is two-pole, which at 50 Hz gives a synchronous speed of 3,000 rpm. The rated voltage is 415 V. The housing is frame size 90. The protection class is IP55, IP56 and IP65. The efficiency is 83 per cent at full load, 83.1 per cent at 75 per cent load and 81.1 per cent at half load. The motor is built in Spain. The figures come from the Australian MEPS register under the GEMS Determination 2012; measured to IEC 60034-2-1 (Edition 2.0). Rated output across the ABB range ranges from 0.75 to 185 kW; the M3BP 90SLB2 sits at the bottom of that range with 1.5 kW. Its immediate neighbours are the M3VRF/S80B2 below it with 1.1 kW and the M3BP 112MJ 6L above it with 2 kW. 2143 ABB models across 2 series are on record. The model is listed under Electric motors. 25 verified figures from 1 source are on file.

ABB M3BP – process performance motors in cast-iron frames: frame sizes 80 to 355, 0.75 to 185 kW, how to read the type code

M3BP is ABB's standard three-phase motor with a cast-iron frame for the process industries – pumps, fans, compressors and conveyors in chemicals, paper, water and mining. The type code follows ABB's system: M for motor, 3 for the generation, B for the cast-iron frame, P for 'process performance'. Then come the IEC frame size (shaft height in mm), the frame length letter (S, M, L with sub-variants A to F) and the number of poles – 'M3BP 132 SMB 4' is therefore a four-pole motor with a 132 mm shaft height in medium length. Trailing letters such as B, G or L mark the winding and voltage variant.

Read on 3 more paragraphs

In the register the series comprises 364 versions from frame size 80 to 355 with rated outputs from 0.75 to 185 kW, two- to eight-pole. Full-load efficiencies run from 74.1 % on the smallest to 97.2 % on the large motors; the data come from energy-efficiency registrations that list efficiency at 50, 75 and 100 % load for each type. Protection is at least IP55 throughout, mostly optionally up to IP66, and mounting arrangements range from B3 (foot) through B5 and B35 (flange) to the vertical forms V1 to V6. Finland, Poland, India and China are recorded as manufacturing locations.

The cast-iron frame distinguishes the M3BP from its aluminium sibling M3AA: it is heavier, stiffer, more resistant to chemicals and allows higher bearing loads – the motors recorded in the register weigh 16 to 1,065 kg.

When buying or replacing, what matters is frame size and mounting (shaft height and flange dimensions are standardised in IEC 60072 and thus interchangeable between makers), the efficiency class to IEC 60034-30 (IE2 or IE3 depending on year and market) and suitability for inverter duty.

Sources: Kennwerte der Modelle ABB M3BP (MEPS-Registrierungen), ABB IEC-Niederspannungsmotoren (Hersteller), ABB Line Card IEC Low voltage motors (2019)

Technical data

Engine

Engine familyM2/M3correct
Engine familiesM2/M3correct
Rated output1.5 kWcorrect

Electrical data

Rated voltage415 Vcorrect
Number of poles2correct
Protection classIP55, IP56, IP65correct
Frame size90correct
Mounting (IEC 60034-7)B3, B5, B8, B14, B35, V1, V3, V5, V6, V18correct
Efficiency at full load83 %correct
Efficiency at 75 % load83.1 %correct
Efficiency at half load81.1 %correct

Origin and approval

Country of manufactureSpaincorrect

Other data

Standard appliedGreenhouse and Energy Minimum Standards (Three Phase Electric Motors) Determination 2012correct
Test methodIEC 60034-2-1 (Edition 2.0)correct

Frequently asked questions

How much power does the ABB M3BP 90SLB2 have?

The ABB M3BP 90SLB2 delivers 1.5 kW.

What to check before buying

  • Match the data plate against the order: frame size, mounting and rating have to agree.
  • Check the ingress rating against the installation site — outdoors or in dust the demands differ.
  • Hold the mounting form and dimensions against the existing seat before ordering.
  • The pole count sets the speed — when replacing an older unit, compare this first.
  • For used units, ask about winding condition and bearing play.
  • Ask about parts availability for this series — the running costs hang on it.

A general list for this type of machine — no substitute for an inspection or an appraiser.

Looking for this machine?
We do not sell machines. We ask the dealers who carry this model and come back with price and lead time.
Request a quote →
Need parts for this model?
We ask the suppliers and come back with price and lead time.
Request spare parts →

This page carries 25 individual figures for this model. They come from 1 recorded source; every figure can be traced there. What we cannot document is not here — we leave gaps open rather than estimate them.

Missing a figure you were looking for? Report it →

Know this machine better? Have a photo, a manual, or know that a figure is wrong? Add it to the register →

Other models in this series

Sources: [1]

Electric motor in 3D section

Turn the model, look inside and click an assembly — each one is explained.

Compare